Hello, I configured my ipv6 tunnel. My files of configuration are following:
[/quote]
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
auto he-ipv6
auto sit0
# Interfaccia di rete interna
iface eth0 inet static
address 192.168.15.100 <--- Lan Ip Server
netmask 255.255.255.0
broadcast 192.168.15.255
gateway 192.168.15.1 <--- Lan Ip Router
iface he-ipv6 inet6 v4tunnel
endpoint 216.66.80.98
ttl 64
iface sit0 inet6 static
address 2001:470:25:537::2
netmask 64
up ip -6 route add default dev he-ipv6
down ip -6 route del default he-ipv6
[/quote]
[/quote]
root@ns:/etc/network# ifconfig
eth0 Link encap:Ethernet HWaddr 00:1b:21:09:87:8d
indirizzo inet:192.168.15.100 Bcast:192.168.15.255 Maschera:255.255.255.0
indirizzo inet6: fe80::21b:21ff:fe09:878d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1102 errors:0 dropped:0 overruns:0 frame:0
TX packets:915 errors:0 dropped:0 overruns:0 carrier:0
collisioni:0 txqueuelen:1000
Byte RX:169592 (169.5 KB) Byte TX:135368 (135.3 KB)
he-ipv6 Link encap:IPv6 in IPv4
indirizzo inet6: fe80::c0a8:f64/64 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:50 errors:0 dropped:0 overruns:0 frame:0
TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
collisioni:0 txqueuelen:0
Byte RX:23696 (23.6 KB) Byte TX:7496 (7.4 KB)
lo Link encap:Loopback locale
indirizzo inet:127.0.0.1 Maschera:255.0.0.0
indirizzo inet6: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:384 errors:0 dropped:0 overruns:0 frame:0
TX packets:384 errors:0 dropped:0 overruns:0 carrier:0
collisioni:0 txqueuelen:0
Byte RX:46093 (46.0 KB) Byte TX:46093 (46.0 KB)
sit0 Link encap:IPv6 in IPv4
indirizzo inet6: ::192.168.15.100/96 Scope:Compat
indirizzo inet6: ::127.0.0.1/96 Scope:Unknown
indirizzo inet6: 2001:470:25:537::2/64 Scope:Global
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisioni:0 txqueuelen:0
Byte RX:0 (0.0 B) Byte TX:0 (0.0 B)
[/quote]
[/quote]
root@ns:/etc/network# ping6 irc6.tophost.it
PING irc6.tophost.it(irc6.tophost.it) 56 data bytes
64 bytes from irc6.tophost.it: icmp_seq=1 ttl=60 time=34.5 ms
64 bytes from irc6.tophost.it: icmp_seq=2 ttl=60 time=37.8 ms
64 bytes from irc6.tophost.it: icmp_seq=3 ttl=60 time=36.5 ms
64 bytes from irc6.tophost.it: icmp_seq=4 ttl=60 time=35.5 ms
64 bytes from irc6.tophost.it: icmp_seq=5 ttl=60 time=34.0 ms
^C
--- irc6.tophost.it ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4004ms
rtt min/avg/max/mdev = 34.068/35.713/37.847/1.371 ms
[/quote]
[/quote]
root@ns:/etc/network# traceroute6 irc6.tophost.it
traceroute to irc6.tophost.it (2001:4b78::6667) from 2001:470:25:537::2, 30 hops max, 16 byte packets
1 linuxgate-1.tunnel.tserv23.zrh1.ipv6.he.net (2001:470:25:537::1) 33.61 ms 33.669 ms 34.965 ms
2 gige-g2-20.core1.zrh1.he.net (2001:470:0:11d::1) 40.672 ms 30.672 ms 30.703 ms
3 10gigabitethernet1-2.core1.mil1.he.net (2001:470:0:217::2) 34.204 ms 34.23 ms 34.697 ms
4 seeweb-v6.mix-it.net (2001:7f8:b:100:1d1:a5d1:2637:86) 34.956 ms 34.786 ms 36.938 ms
5 irc6.tophost.it (2001:4b78::6667) 33.167 ms 34.281 ms 35.438 ms
[/quote]
[/quote]
In sysctl.conf I have set
net.ipv6.conf.all.forwarding=1
[/quote]
now you say what's the problem? The problem is that it does not connect to ircnet :
[/quote]
tcp6 0 0 ip6-localhost:953 [::]:* LISTEN 1061/named
tcp6 0 0 localhost:8005 [::]:* LISTEN 1243/java
tcp6 0 1 linuxgate-1-pt.tu:40050 irc6.tophost.it:ircd SYN_SENT 1887/psybnc
[/quote]
In Cisco router I disabled DMZ setting but NAT is enabled and only two ports point to the local ip of the router and are open to the outside. HELP ME PLEASE !
Irc is blocked by default unless you have earned the sage certification
Quote from: cholzhauer on October 07, 2012, 06:46:35 AM
Irc is blocked by default unless you have earned the sage certification
How do I get that certification?
http://ipv6.he.net/certification/
Quote from: cholzhauer on October 07, 2012, 07:12:24 AM
http://ipv6.he.net/certification/
I did and I was granted certification but irc still does not work
You're only a newbie...you need to become sage
http://ipv6.he.net/certification/scoresheet.php?pass_name=linuxgate
Quote from: cholzhauer on October 07, 2012, 07:25:26 AM
You're only a newbie...you need to become sage
http://ipv6.he.net/certification/scoresheet.php?pass_name=linuxgate
How do I get sage?
I completed the test and got the certification SAGE, but the connection to irc still does not work, why?
Log into the broker, go to your tunnel's details page, there should be a button to unblock IRC access.
Thanks