hi..
i did configure ipv6 for two NIC cards, first i have eth1 to configure ipv6, i did configure and it works but suddenly someone that NIC card. so i have to re-conf it (eth2) but those both card gave different result:
eth0 Link encap:Ethernet HWaddr 00:26:18:EE:C6:4F
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:28 Base address:0xe000
eth1 Link encap:Ethernet HWaddr 00:24:01:D2:2B:D1
inet addr:202.47.88.XX Bcast:202.47.88.79 Mask:255.255.255.240
inet6 addr: fe80::224:1ff:fed2:2bd1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:311913 errors:0 dropped:0 overruns:0 frame:0
TX packets:105610 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:102114023 (97.3 MiB) TX bytes:13764699 (13.1 MiB)
Interrupt:20 Base address:0x8c00
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: 2001:470:35:XXX::2/64 Scope:Global
inet6 addr: fe80::ca2f:584c/128 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:1410 dropped:0 overruns:0 carrier:1410
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1593 errors:0 dropped:0 overruns:0 frame:0
TX packets:1593 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:224484 (219.2 KiB) TX bytes:224484 (219.2 KiB)
sit0 Link encap:IPv6-in-IPv4
inet6 addr: ::202.47.88.XX/96 Scope:Compat
inet6 addr: ::127.0.0.1/96 Scope:Unknown
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sit1 Link encap:IPv6-in-IPv4
inet6 addr: fe80::ca2f:5843/64 Scope:Link
inet6 addr: 2001:470:35:XXX::2/64 Scope:Global
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:92 errors:0 dropped:0 overruns:0 frame:0
TX packets:172 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17746 (17.3 KiB) TX bytes:125612 (122.6 KiB)
while for eth2 it doesnt have sit0 and sit1, why? what is sit1 and sit0 exactly?
eth0 Link encap:Ethernet HWaddr 00:26:18:EE:C6:4F
inet addr:202.47.88.67 Bcast:202.47.88.79 Mask:255.255.255.240
inet6 addr: fe80::226:18ff:feee:c64f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:628364 errors:0 dropped:0 overruns:0 frame:0
TX packets:10502 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:67415880 (64.2 MiB) TX bytes:2127919 (2.0 MiB)
Interrupt:28 Base address:0xa000
eth2 Link encap:Ethernet HWaddr 00:40:F4:EA:7D:DD
inet addr:172.27.11.66 Bcast:172.27.11.255 Mask:255.255.255.0
inet6 addr: fe80::240:f4ff:feea:7ddd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:327438 errors:336305 dropped:292246 overruns:336305 frame:0
TX packets:838 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:31261577 (29.8 MiB) TX bytes:86715 (84.6 KiB)
Interrupt:20 Base address:0x4c00
he-ipv6 Link encap:IPv6-in-IPv4
inet6 addr: fe80::ca2f:5843/128 Scope:Link
inet6 addr: 2001:470:35:270::2/64 Scope:Global
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:459 errors:0 dropped:0 overruns:0 frame:0
TX packets:589 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:394222 (384.9 KiB) TX bytes:90240 (88.1 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:145 errors:0 dropped:0 overruns:0 frame:0
TX packets:145 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14879 (14.5 KiB) TX bytes:14879 (14.5 KiB)
Quote from: gudboy1 on November 17, 2011, 09:37:54 PM
while for eth2 it doesnt have sit0 and sit1, why? what is sit1 and sit0 exactly?
sit0 and sit1 are virtual interfaces that you created when you created the tunnel to talk to HE
See this for more info
http://en.wikipedia.org/wiki/IPv6#Transition_mechanisms
why it gives different result? i did the same configuration for both..