Hello.
I've tried to set up the tunnel service by HE, but had no luck so far.
The tunnel adapter always shows Media disconnected, i suppose that's not correct?
Pinging local IP6s work, but not the IP6 the HE gave me as the other end of the tunnel and gateway.
Obviously, no IP6 addresses are accessible.
My ISP is IPv6 aware, and i don't think they block protocol 41 (but it can be blocked somewhere way upstream "just in case" due to retadedness of local business practices. Is there any kind of a way to check? Google does not help much).
There are no routers on my part of the cable, only a hab.
I have a static external IP that can be used to access any service i set on the this system, and which is my endpoint on this side.
What can be wrong?
The stats:
Commands used, with several permutations after clean resets:
netsh interface teredo set state disabled
netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel 91.206.***.*** 216.66.80.26
netsh interface ipv6 add address interface=IP6Tunnel 2001:470:1f08:143e::2
netsh interface ipv6 add route ::/0 interface=IP6Tunnel 2001:470:1f08:143e::1
ipconfig /all:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : kurkino.net.ru
Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
Physical Address. . . . . . . . . : 00-50-22-E1-07-E0
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:470:1f09:143e::2(Preferred)
Link-local IPv6 Address . . . . . : fe80::7570:5312:aa9e:7b84%11(Preferred)
IPv4 Address. . . . . . . . . . . : 10.0.92.34(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : 4 февраля 2011 г. 13:18:57
Lease Expires . . . . . . . . . . : 11 февраля 2011 г. 13:18:56
Default Gateway . . . . . . . . . : 2001:470:1f08:143e::1
10.0.92.1
DHCP Server . . . . . . . . . . . : 127.0.0.1
DHCPv6 IAID . . . . . . . . . . . : 244377274
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-7E-02-D5-90-E6-BA-15-36-E7
DNS Servers . . . . . . . . . . . : 91.206.14.254
91.206.15.254
91.206.14.6
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter IP6Tunnel:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Direct Point-to-point Adapater
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
route print:
===========================================================================
Interface List
11...00 50 22 e1 07 e0 ......Realtek PCIe GBE Family Controller
1...........................Software Loopback Interface 1
18...00 00 00 00 00 00 00 e0 Microsoft Direct Point-to-point Adapater
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 10.0.92.1 10.0.92.34 20
10.0.0.0 255.0.0.0 10.0.92.2 10.0.92.34 21
10.0.92.0 255.255.255.0 On-link 10.0.92.34 276
10.0.92.34 255.255.255.255 On-link 10.0.92.34 276
10.0.92.255 255.255.255.255 On-link 10.0.92.34 276
81.19.85.0 255.255.255.0 10.0.92.2 10.0.92.34 21
91.206.14.0 255.255.255.192 10.0.92.2 10.0.92.34 21
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
169.254.0.0 255.255.0.0 On-link 10.0.92.34 30
169.254.255.255 255.255.255.255 On-link 10.0.92.34 276
192.168.56.0 255.255.255.0 On-link 192.168.56.1 276
192.168.56.1 255.255.255.255 On-link 192.168.56.1 276
192.168.56.255 255.255.255.255 On-link 192.168.56.1 276
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.56.1 276
224.0.0.0 240.0.0.0 On-link 10.0.92.34 276
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.56.1 276
255.255.255.255 255.255.255.255 On-link 10.0.92.34 276
===========================================================================
Persistent Routes:
None
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
11 276 ::/0 2001:470:1f08:143e::1
1 306 ::1/128 On-link
11 276 2001:470:1f09:143e::/64 On-link
11 276 2001:470:1f09:143e::2/128
On-link
17 276 fe80::/64 On-link
11 276 fe80::/64 On-link
17 276 fe80::20:a2ba:9532:e321/128
On-link
11 276 fe80::7570:5312:aa9e:7b84/128
On-link
1 306 ff00::/8 On-link
17 276 ff00::/8 On-link
11 276 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
ping 2001:470:1f08:143e::1 does not reply.
Pinging 2001:470:1f08:143e::1 with 32 bytes of data:
Destination host unreachable.
Because you didn't use your 10.x address to create the tunnel
Change your 91.206.x to 10.x
>>Because you didn't use your 10.x address to create the tunnel
Hm? That's a private network IP, the HE system won't even allow it.
There's two different spots.
On the HE website, you need to use your public address, whatever it is.
When you did this...
netsh interface teredo set state disabled
netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel 91.206.***.*** 216.66.80.26
netsh interface ipv6 add address interface=IP6Tunnel 2001:470:1f08:143e::2
netsh interface ipv6 add route ::/0 interface=IP6Tunnel 2001:470:1f08:143e::1
You need to do this
netsh interface teredo set state disabled
netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel 10.0.92.34 216.66.80.26
netsh interface ipv6 add address interface=IP6Tunnel 2001:470:1f08:143e::2
netsh interface ipv6 add route ::/0 interface=IP6Tunnel 2001:470:1f08:143e::1
Because you're behind a NAT device.
Okay, i removed it and tried with
netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel 10.0.92.1 216.66.80.26
netsh interface ipv6 add address interface=IP6Tunnel 2001:470:1f08:143e::2
But there is no appreciable effect, it won't ping 2001:470:1f08:143e::1 still.
Oops, wrong address.
With netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel 10.0.92.34 216.66.80.26 it seems to work!
Ok, i clean and reset later everything works, i can get to ipv6.google.
Thank you for help.
Why are these details not described in a FAQ or guidelines?
Or, have i missed them?
They are, you missed them ;)
Quote
*NOTE* When behind a firewall appliance that passes protocol41, instead of using the IPv4 endpoint you provided to our broker, use the IPv4 address you get from your appliance's DHCP service.
This is below the commands you copied and pasted off the tunnel broker page
They are... (http://orbiter-forum.com/images/smilies/blush.gif)
I guess "firewall appliance" didn't resolve into "ISP's NAT".
One more thing - whatever address i set, http://ipv6.whatismyipv6.com gives me 2001:470:1f08:143e::2 as mi IP6.
Is that normal?
Did you leave that other address set on your LAN connection? It should show whatever IP is on your LAN connection, but I can't say for sure because I don't use Windows as my tunnel router
Well, I take that back. If I ping something from my tunnel router, the ping starts from my ::2 address even though I've assigned an IPv6 address to my Ethernet adapter.
So I'll say yes, that's normal.
You should keep the address assigned to your LAN connection though so you can route other traffic