Hi folks,
just wanna seek your assistance with regards to the tunnel configuration on windows 7. my situation goes like this, i can monitor that the tunnel is up but i can't ping ipv6.google.com and also my default ipv6 gateway.
below is the config
netsh interface teredo set state disabled
netsh interface ipv6 add v6v4tunnel IP6Tunnel 192.168.3.3 216.218.221.6
netsh interface ipv6 add address IP6Tunnel 2001:470:18:c0e::2
netsh interface ipv6 add route ::/0 IP6Tunnel 2001:470:18:c0e::1
here's the capture output from my command prompt
C:\Windows\system32>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Carlo-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : smartbro.net
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : smartbro.net
Description . . . . . . . . . . . : Realtek PCIe FE Family Controller
Physical Address. . . . . . . . . : 00-26-18-03-0F-5E
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::92a:fe77:7362:7440%11(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.3.3(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.248
Lease Obtained. . . . . . . . . . : Tuesday, April 24, 2012 3:16:11 PM
Lease Expires . . . . . . . . . . : Tuesday, May 01, 2012 2:09:16 PM
Default Gateway . . . . . . . . . : 192.168.3.1
DHCP Server . . . . . . . . . . . : 192.168.3.1
DHCPv6 IAID . . . . . . . . . . . : 251667992
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-D1-FB-42-00-26-18-03-0F-5E
DNS Servers . . . . . . . . . . . : 121.1.3.81
121.1.3.16
121.1.3.66
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter IP6Tunnel:
Connection-specific DNS Suffix . : smartbro.net
Description . . . . . . . . . . . : Microsoft Direct Point-to-point Adapater
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:470:c:44e::2(Preferred)
IPv6 Address. . . . . . . . . . . : 2001:470:18:c0e::2(Preferred)
Link-local IPv6 Address . . . . . : fe80::15d5:2183:ee8:6236%12(Preferred)
Default Gateway . . . . . . . . . : 2001:470:18:c0e::1
DNS Servers . . . . . . . . . . . : 121.1.3.81
121.1.3.16
121.1.3.66
NetBIOS over Tcpip. . . . . . . . : Disabled
C:\Windows\system32>netsh int ipv6 sh int
Idx Met MTU State Name
--- ---------- ---------- ------------ ---------------------------
1 50 4294967295 connected Loopback Pseudo-Interface 1
12 40 1280 connected IP6Tunnel
11 30 1500 connected Local Area Connection
hope you can help me :-) thanks in advance
How can you be sure your tunnel is up if you can't ping the HE side of the tunnel?
I think your problem is here
IPv6 Address. . . . . . . . . . . : 2001:470:c:44e::2(Preferred)
IPv6 Address. . . . . . . . . . . : 2001:470:18:c0e::2(Preferred)
You have two different IP addresses on your IP6Tunnel adapter. Remove the one you don't need and see what you get