Hurricane Electric's IPv6 Tunnel Broker Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to Hurricane Electric's Tunnelbroker.net forums!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - cholzhauer

Pages: [1] 2 3 ... 169
1
Questions & Answers / Re: Tunnel behind Carrier grade nat
« on: March 23, 2017, 01:17:56 PM »
The short answer is no

2
General Discussion / Re: Unable to establish Ipv6 connectivity
« on: March 13, 2017, 05:30:02 PM »
Quote
In which case, an obvious suggestion is: you might try putting the windows machine in the DMZ.

You make a good point.  On some routers this works, on some it doesn't.  Best way to find out is to just try.

3
General Discussion / Re: Unable to establish Ipv6 connectivity
« on: March 13, 2017, 04:54:14 PM »
Quote
While I don't know the full details of 6in4, I'm not sure how well it will work through the NAT firewall. 

6in4 has no issue with NAT as long as the router knows what's going on and is able to pass the traffic without bothering it.
Quote
You might try seeing if you can configure the tunnel directly on the TP Link router.

You are correct that it would be easier to host the tunnel on the router, but older routers and cheaper routers don't normally have this option.
Quote
you might try putting your 112.xxx.xxx.xxx address in the localaddress= value. [guessing]

That'll make things worse, the 192.x is appropriate here.

4
General Discussion / Re: Unable to establish Ipv6 connectivity
« on: March 13, 2017, 06:48:21 AM »
Sounds like protocol 41 might be an issue...does your ISP block it?

You can run wireshark to see if you're getting any incoming packets.

5
Questions & Answers / Re: Testing protocol 41
« on: February 22, 2017, 12:04:17 PM »
You would use something like wire shark to look at incoming packets, but as was mentioned, it won't normally work with CGN

6
Questions & Answers / Re: Using TunnelBroker for several routers
« on: February 22, 2017, 06:53:17 AM »
FWIW, even if you had a /48, you'd have to use a /64 for RA as that's what it expects; entering /48 there would break it.

7
Questions & Answers / Re: Using TunnelBroker for several routers
« on: February 22, 2017, 06:33:39 AM »
You need to fill out the "IPv6 LAN Setting" box for your router to do RA for the rest of your network.

8
Questions & Answers / Re: Using TunnelBroker for several routers
« on: February 22, 2017, 04:37:19 AM »
Yep, what he said ^

One router runs the tunnel, the others get an address from that one via RA or by you manually configuring them

9
Questions & Answers / Re: POP tserv1.ber1.he.net down?
« on: February 21, 2017, 05:46:20 AM »
Have you emailed ipv6@he.net to open a ticket?

10
Questions & Answers / Re: how to create a ubuntu-box server ivp6
« on: February 20, 2017, 12:51:40 PM »
I've never used wifi...you can't use wired?

11
Questions & Answers / Re: how to create a ubuntu-box server ivp6
« on: February 19, 2017, 05:16:38 PM »
So it sounds like you have a problem with your SLAAC setup.

12
Questions & Answers / Re: how to create a ubuntu-box server ivp6
« on: February 17, 2017, 11:43:37 AM »
Your other clients are not getting IPv6 addresses?

13
I do something like this; my firewall is an ASA and you can't create a tunnel on there.  I stood up a FreeBSD VM outside of the firewall and terminated my tunnel on it.  Then, all traffic that comes through my firewall and I can filter it as needed.

14
Questions & Answers / Re: Download limit?
« on: February 10, 2017, 09:33:27 AM »
No limit, just be responsible about it.

15
Questions & Answers / Re: HE IPv6 Tunnel terrible bandwidth
« on: February 01, 2017, 10:43:03 AM »
I'm not familiar with the tunnel IP scheme...where is your tunnel located?

Pages: [1] 2 3 ... 169