Hurricane Electric's IPv6 Tunnel Broker Forums

Advanced search  

News:

Welcome to Hurricane Electric's Tunnelbroker.net forums!

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - xiecong520

Pages: [1]
1
I'm sorry, but this article by the translation software.

Using EPON fiber mode equipment. pppoe access network mode.

It has routing functions, but does not support the tunnel proxy.

Therefore, I use the private address on Windows 192.168.1.2 instead deploy tunnel proxy.

Owing to the bad NAT performance,Now switch to the Windows directly PPPOE dial.

Seems everything is all right now, I'm relieved.


Now has a stable, every time I restart the computer. The tunnel will fail. Because the pppoe dynamic.

I'm trying to deploy tunnel. "add v6v4tunnel interface=IP6Tunnel localaddress="    alternative to using the following parameters:

 localaddress = "PPPOE" parameters of the localaddress = 0.0.0.0 or localaddress = 127.0.0.1.  prompt parameter error, no success.

I also try to add the tunnel server ipv4 addresses the static routing, also invalid. Ask, is there a script automatically, or you can forward how to set up?

2

Support the building Lord. Good idea..
A good example. For example, I am a Chinese user. Ipv6 deployment is relatively backward.
Connect to Hong Kong will want to route to the United States. Delay doubled.

The United States:
PS C:\Users\xxxx> tracert -d 66.220.18.42
通过最多 30 个跃点跟踪到 66.220.18.42 的路由
  1    <1 毫秒   <1 毫秒   <1 毫秒 192.168.100.1
  2     1 ms     1 ms     1 ms  119.xxx.xxx.1
  3     3 ms     3 ms     3 ms  58.51.97.33
  4     7 ms     *        4 ms  58.51.97.21
  5    17 ms    19 ms     *     202.97.67.1
  6    22 ms    25 ms    24 ms  202.97.33.106
  7     *       21 ms    24 ms  202.97.91.198
  8   189 ms   191 ms   191 ms  202.97.52.222
  9   282 ms   277 ms   275 ms  202.97.49.106
 10   179 ms   179 ms   179 ms  64.62.244.61
 11   238 ms   253 ms   250 ms  72.52.92.121
 12   178 ms   178 ms   179 ms  66.220.18.42
跟踪完成。

Hong Kong:
PS C:\Users\xxxx> tracert -d 216.218.221.6
通过最多 30 个跃点跟踪到 216.218.221.6 的路由
  1    <1 毫秒   <1 毫秒   <1 毫秒 192.168.100.1
  2     1 ms     1 ms     1 ms  119.xxx.xxx.1
  3     2 ms     3 ms     3 ms  58.51.97.33
  4     4 ms     3 ms     3 ms  58.51.97.21
  5    17 ms     *       18 ms  202.97.67.49
  6    20 ms    18 ms    19 ms  202.97.33.118
  7     *        *       21 ms  202.97.91.206
  8   177 ms   174 ms     *     202.97.51.114
  9   230 ms     *      224 ms  202.97.50.26
 10   171 ms   170 ms   172 ms  64.62.244.61
 11   365 ms   362 ms   362 ms  184.105.64.126
 12  493 ms   332 ms   332 ms  216.218.221.6
跟踪完成。

3
Questions & Answers / Re: Windows 10
« on: May 06, 2017, 01:31:08 AM »
ipconfig /flushdns
netsh int ipv6 delete neighbors
netsh int ipv6 delete destinationcache
netsh int ipv4 delete neighbors
netsh int ipv4 delete destinationcache
netsh int ipv6 reset
netsh int ipv4 reset
netsh winsock reset

restart the computer

ipconfig /registerdns
netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel localaddress=192.168.1.3 remoteaddress=216.66.80.98
netsh interface ipv6 add address interface=IP6Tunnel address=2001:470:25:64d::2
netsh interface ipv6 add route prefix=::/0 interface=IP6Tunnel nexthop=2001:470:25:64d::1
netsh interface ipv6 add dnsservers "Wi-Fi" 2001:4860:4860::8888  index=1
netsh interface ipv6 delete route ::/0 ""Wi-Fi"" fe80::1

If you can't. 
  ping 216.66.80.98   or    tracert -d 216.66.80.98
  ping -6 2001:470:25:64d::1    or   tracert -d 2001:470:25:64d::1
  [ing -6 2001:4860:4860::8888    or    tracert -d 2001:4860:4860::8888
Look at the problem in where

4
Questions & Answers / Re: Windows 10
« on: April 16, 2017, 11:43:50 PM »
netsh interface ipv6 add dnsservers "Wi-Fi" 2001:470:20::2 index=1

Try the above command, such as not not. Please try the following command

netsh interface isatap set state disabled
netsh interface 6to4 set state disabled
netsh interface teredo set state disabled
netsh interface ipv6 delete interface "IP6Tunnel*"
route -f
netsh interface ipv6 reset

After input the above command, restart the computer.

netsh interface ipv6 add v6v4tunnel interface=IP6Tunnel localaddress=192.168.1.3 remoteaddress=216.66.80.98
netsh interface ipv6 add address interface=IP6Tunnel address=2001:470:25:64d::2
netsh interface ipv6 add route prefix=::/0 interface=IP6Tunnel nexthop=2001:470:25:64d::1


Once again, restart the computer.  OK

Pages: [1]