Deleted

[tombayo]

Deleted

[cholzhauer]

The way I want it to work is that the IPv6 Addresses are assigned like this:
The server gets: 2001:470:27:39a::50
The clients: 2001:470:27:39a::100-200


Is this even possible?

To do that you'll need DHCPv6;  RA will only give you addresses based on the MAC address.

There's a DHCP role in Server 2008 that should do what you want

[nickbeee]

You don't route the tunnel interface /64 into your LAN. It's used purely for the point-to-point link.

You will need to use a routed /64 or /48 which you can see on your tunnel details page. Based on the addressing you have given, your routed /64 is likely to be 2001:470:28:39a::1/64.

[nickbeee]

Does your 2008 server have routing and remote access configured?

[cholzhauer]

You'll need to tell your computers to get their IPv6 addresses from a DHCPv6 server and not RA.

To do that, you'll need to set the correct flags

http://blogs.technet.com/b/teamdhcp/archive/2009/02/12/dhcp-broadcast-flag-handling-in-windows-7.aspx

http://blogs.technet.com/b/teamdhcp/archive/tags/ipv6/

[liuxyon]

I have the same question. I have done normal work for windows 2003. but it can't normal worke for win 2008. I looking for it also.

[cholzhauer]

Looking for what? RRAS config?

[liuxyon]

use windows netsh command.

[cholzhauer]

You really should open your own thread

Code Select Expand


Steps below were done in Vista.  Steps for Windows 7 might be a little different.

1.  Open Regedit, navigate to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\TCPIP6\Parameters
Add STRING value called 'DisabledComponents' and set its value to 0; Reboot
Open the LAN adapter properties and open the IPv6 properties
Manually add an address from this subnet: 2001:db8:1f07:e9a::/64
Keep the prefix at 64
Add this gateway: 2001:db8:1f06:e9a::1
Add this DNS server: 2001:db8:200::2 (this is one of HE's DNS servers)
Click OK and OK to save the changes
Open 'cmd' and type the following commands
netsh interface teredo set state disabled
netsh interface ipv6 add v6v4tunnel IP6Tunnel <your local IP address> 216.66.22.2
netsh interface ipv6 add address IP6Tunnel 2001:db8:1f06:e9a::2
netsh interface ipv6 add route ::/0 IP6Tunnel 2001:db8:1f06:e9a::1

10.  Test IPv6 connectivity by pinging or opening a website like ipv6.google.com

Steps to configure host to act as IPv6 router

1.  In CMD type: netsh int ipv6 set interface IP6Tunnel forwarding=enabled
2.  Next, type: netsh int ipv6 set interface "Local Area Connection" forwarding=enabled advertise=enabled
3.  Next, add the first address of the routed IP address to the Local Area Connection
netsh int ipv6 add address "Local Area Connection" 2001:db8:8:a0a::1
4.  Next, add the default route and next hop for the tunnel and Local Area Connection, then publish it:
netsh int ipv6 set route 2001:db8:8:a0a::/64 "Local Area Connection" publish=yes
5.  Next, add the default route for the tunnel and publish it:
netsh interface ipv6 set route ::/0 IP6Tunnel 2001:db8:7:a0a::1 publish=yes


You will obviously need to change the IPv6 addresses so they reflect your assigned tunnels