Hurricane Electric's IPv6 Tunnel Broker Forums

General IPv6 Topics => IPv6 on Routing Platforms => Topic started by: rsreese on November 11, 2008, 09:23:08 PM

Title: Allow lan hosts to autoconfigure through Cisco router
Post by: rsreese on November 11, 2008, 09:23:08 PM
I was trying to follow the post here: http://www.tunnelbroker.net/forums/index.php?topic=224.0 that was very helpful but I don't think I quite have it. My clients (Vista, Debian) don't seem to be auto configuring themselves since they still have still have link-local addresses?

Tunnel connection.
Code: [Select]
#sh ipv6 int tunnel 0
Tunnel0 is up, line protocol is up
  IPv6 is enabled, link-local address is FE80::4C12:XXXX
  Description: HE.net
  Global unicast address(es):
    2001:470:XXXX:XXXX::2, subnet is 2001:470:1F06:3B6::/64
  Joined group address(es):
    FF02::1
    FF02::2
    FF02::1:FF00:2
    FF02::1:FF12:CAB4
  MTU is 1480 bytes
  ICMP error messages limited to one every 100 milliseconds
  ICMP redirects are enabled
  ND DAD is enabled, number of DAD attempts: 1
  ND reachable time is 30000 milliseconds

Internal interface to clients.
Code: [Select]
interface FastEthernet0/1.2
 description $FW_INSIDE$
 encapsulation dot1Q 2
 ip address 172.16.2.1 255.255.255.0
 ip access-group 101 in
 no ip unreachables
 ip nat inside
 ip virtual-reassembly
 ipv6 address 2001:470:XXXX::1/64
 ipv6 enable

Vista
Code: [Select]
Ethernet adapter Local Area Connection:

   Connection-specific DNS Suffix  . :
   Link-local IPv6 Address . . . . . : fe80::11a:dfa3:1034:a11f%8
   IPv4 Address. . . . . . . . . . . : 172.16.2.2
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 172.16.2.1
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: rsreese on November 20, 2008, 07:17:10 PM
^^bump^^

 ;D
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: evilzardoz on November 26, 2008, 12:24:40 AM
Hi,

You need to advertise your subnet using neighbour discovery:

ipv6 nd prefix 2001:470:XXXX::/64 infinite infinite

the two last commands define how long the IPv6 addresses 'last'

Note that you won't get DNS servers advertised to clients this way.  That requires DHCPv6 which unfortunately isn't well supported yet...
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: spectre240sx on February 22, 2009, 09:19:41 PM
What routing platform are you on? I've got a 2621xm and my router issued RAs by default. My ASA5505 does the same thing.
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: rsreese on April 04, 2009, 06:17:04 PM
Hi,

You need to advertise your subnet using neighbour discovery:

ipv6 nd prefix 2001:470:XXXX::/64 infinite infinite

the two last commands define how long the IPv6 addresses 'last'

Note that you won't get DNS servers advertised to clients this way.  That requires DHCPv6 which unfortunately isn't well supported yet...

I applied
Code: [Select]
ipv6 nd prefix 2001:470:xxxx:xxx::/64 infinite infinite
to the internal interface f0/1.2 but my client didn't seem to pickup the IP from the router? Which ipv6 IP should I be using?
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: rsreese on April 05, 2009, 08:26:07 PM
Here's what my internal interface looks like.



Code: [Select]
#sh ipv6 int f0/1.2
FastEthernet0/1.2 is up, line protocol is up
  IPv6 is enabled, link-local address is FE80::20C:85FF:FE07:A701
  Description: $FW_INSIDE$
  Global unicast address(es):
    2001:470:XXXX::1, subnet is 2001:470:880D::/64
  Joined group address(es):
    FF02::1
    FF02::2
    FF02::1:FF00:1
    FF02::1:FF07:A701
  MTU is 1500 bytes
  ICMP error messages limited to one every 100 milliseconds
  ICMP redirects are enabled
  ND DAD is enabled, number of DAD attempts: 1
  ND reachable time is 30000 milliseconds
Title: Re: Allow lan hosts to autoconfigure through Cisco router
Post by: rsreese on April 06, 2009, 07:11:19 PM
I didn't have #ipv6 unicast-routing

I've been told three different methods and since I'm also new to this I'm just trying to figure out the benefits to each one. Basically I'm asking why bother with the latter two if the first one works?

ipv6 address 2001:470:880D::1/64

ipv6 nd prefix 2001:470:1F07:3B6::/64 infinite infinite

ipv6 address 2001:470:880D::/64 eui-64