Hi
I got a problem with IPv6-tunneling with my Netgear WPN824v2 router. Im trying to use my tunnel with a laptop running Ubuntu 9.04. I got it working fine with only my modem(my modem dosent have any dhcp or so).
Router WebGUI:
I entred WAN Setup
Connecect Automatically, as Required=ON
Disable SPI Firewall=ON
Default DMZ Server=ON, 192.168.1.3(my laptop)
Respond to Ping on Internet Port=ON
MTU Size (in bytes)=1500 bytes
NAT Filtering=Open
But, it still not work. Does anyone have any idea what I can do? Or does the router make this impossible?
Mendemizo
EDIT: I just discoverd something. When I paste in this in the terminal on my laptop:
ifconfig sit0 up
ifconfig sit0 inet6 tunnel ::209.51.161.14
ifconfig sit1 up
ifconfig sit1 inet6 add 2001:470:1f06:e6::2/64
route -A inet6 add ::/0 dev sit1
I can't enter tunnelbroker.net anymore.
EDIT2:
Information from ifconfig:
eth1 Link encap:Ethernet HWaddr 00:12:f0:89:7e:43
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::212:f0ff:fe89:7e43/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3249 errors:6 dropped:6 overruns:0 frame:0
TX packets:714 errors:0 dropped:6 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:60990095 (60.9 MB) TX bytes:569668 (569.6 KB)
Interrupt:21 Base address:0xa000 Memory:d0400000-d0400fff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:608 (608.0 B) TX bytes:608 (608.0 B)
sit0 Link encap:IPv6-in-IPv4
inet6 addr: ::127.0.0.1/96 Scope:Unknown
inet6 addr: ::192.168.1.3/96 Scope:Compat
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
sit1 Link encap:IPv6-in-IPv4
inet6 addr: 2001:470:1f06:e6::2/64 Scope:Global
inet6 addr: fe80::c0a8:103/64 Scope:Link
UP POINTOPOINT RUNNING NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:568 (568.0 B)
Since you're using an RFC 1918 private network with NAT, first make certain that your IPv4 tunnel endpoint specifies a routable IPv4 address (the address of your NAT device). If you put in 192.168.1.3 instead (a HE's server), then of course your tunnel won't work.
I have the exact same question. Does the Netgear WPN824v2 pass protocol 41? Without the Netgear, directly onto the modem, i got ipv6 working. So everyhing is configured correct.
Then I would say it's not passing protocol 41.
However, like snarked mentioned, you need to use your NAT'd address to create the tunnel
The tunnel is working fine without the netgear. On the hurricane site the ipv4 client adress is: 83.84.22X.XX. The tunnel on my pc is:
netsh interface ipv6 add v6v4tunnel IP6Tunnel 192.168.1.4 216.66.84.46
netsh interface ipv6 add address IP6Tunnel 2001:470:1f14:a8c::2
netsh interface ipv6 add route ::/0 IP6Tunnel 2001:470:1f14:a8c::1
So is there any chance of getting this working with the Netgear (opening a port, disabling firewall?)
Disabling the firewall would let protocol 41 through.
Some routers also have a DMZ..you could try placing your host in there and seeing if that works
Tried to disable SPI firewall and DMZ host but no luck..
Is there any new firmware available?