• Welcome to Hurricane Electric's IPv6 Tunnel Broker Forums.

IPv6 Tunnel Setup

Started by CareyG, May 21, 2011, 09:43:35 AM

Previous topic - Next topic

CareyG

firewall is good, not about what to use for a dummy interface (default gateway) 10.10.2.1 will not work tunnel broker only sees the public ip address and will not allow me to use another address it says it being blocked by firewall and firewall is open ?

cholzhauer

The tunnel broker will only see your public IP address...you need to use the NAT address in the commands you enter into the command prompt

cholzhauer

So your tunnel works now?

If you're not getting DNS, check the DNS server you're using.  What OS?  XP will not use IPv6 transport for DNS lookups.

If you're not seeing an AAAA record when you do a nslookup, your DNS server is not returning them.

Did you enter an IPv6 address on your LAN connections?  The directions from HE only tell you how to add an address to your IP6Tunnel adapter.

CareyG

I have the connection working but i am cheating, here are the errors i am getting!
No IPv6 address detected
IPv6 connections work, but connections using DNS names do not use IPv6. For some reason, your browser or your OS is not doing IPv6 DNS 'AAAA' lookups.


cholzhauer

Quote
I have the connection working but i am cheating,

You'll have to elaborate a little.

Did you see my other suggestions?

CareyG

Ok i added hostfiles to get the urls to work, and went to,test-ipv6.com and that were i saw the errors i listed. on my lan connection i would add the 10. address right and convert to the ipv6 address. Our DNS servers they dont do reverse lookups so i dont think there is much i can do. I am getting there, thanks for the help!

CareyG

My bad important question you asked win 2008 sorry!

cholzhauer

You can use HE's DNS servers instead

No need to convert...use an IP out of the routed /64 range you have listed on your tunnel page

CareyG

No connection now:
C:\Users\Administrator>ipconfig

Windows IP Configuration


Ethernet adapter Client-Server:

   Connection-specific DNS Suffix  . :
   Link-local IPv6 Address . . . . . : fe80::eca6:6408:7743:3439%18
   IPv4 Address. . . . . . . . . . . : 10.10.2.24
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 10.10.2.1

Ethernet adapter Server-Server:

   Connection-specific DNS Suffix  . :
   Link-local IPv6 Address . . . . . : fe80::8997:3820:70b4:1b3a%17
   IPv4 Address. . . . . . . . . . . : 10.10.3.154
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : ::

cholzhauer

I assume you just cut off the IP6Tunnel adapter

You need to assign an IPv6 address to your Server-Server adapter.  I don't know what your /64 is, but you add it the same way you would add a static IPv4 address, but just choose the IPv6 adapter instead.  If your routed /64 was 2001:db8:1:1::/64, you could use 2001:db8:1:1::1 as your address

CareyG

here are my settings i add a IPV6 address to the network tab? does this show available addresses i can use?
IPv6 Tunnel Endpoints
Server IPv4 Address:72.52.104.74Server IPv6 Address:2001:470:1f04:1ceb::1/64Client IPv4 Address:71.164.237.24Client IPv6 Address:2001:470:1f04:1ceb::2/64Available DNS Resolvers
Anycasted IPv6 Caching Nameserver:2001:470:20::2Anycasted IPv4 Caching Nameserver:74.82.42.42Routed IPv6 Prefixes
Routed /64:2001:470:1f05:1cea::/64Routed /48:2001:470:8737::/48 [X]rDNS DelegationsEditDelegate to dns.he.net | SaverDNS Delegated NS1:ns1.he.netrDNS Delegated NS2:ns2.he.netrDNS Delegated NS3:ns3.he.netrDNS Delegated NS4:ns4.he.netrDNS Delegated NS5:ns5.he.net

cholzhauer

Quote
Routed /64:2001:470:1f05:1cea::/64
Routed /48:2001:470:8737::/48

Use 2001:470:1f05:1cea::1 for your server-server adapter

Add the address with these directions

http://technet.microsoft.com/en-us/library/bb878057.aspx

Your gateway will be 2001:470:1f04:1ceb::1

CareyG

still does not work it complains about the server server interface not a dupe. the client server is the interface that connects to the internet.

CareyG

now nothing works except the internet i need to just remove this and start over, dont no what the cli commands are to just remove every thing