I'm a novice at setting up a proxy I have tried to set up and I'm getting this error message:
Error: Your IPv4 endpoint is unreachable or unstable. Please make sure ICMP is not blocked. If you are blocking ICMP, please allow 66.220.2.74 through your firewall.
I have a LAN connection and I have put in my public IP address allowed ICMP pings through Mcafee and allowed 66.220.274 to connect and still the message continues. I'm using windows XP home edition sp3. I am using a siemens ADSL speedstream modem provided by my ISP. If anyone don't mind helping out a complete beginner, I'd be greatful
Thanks
OK, first thing.
is there a firewall in your speedstream? If you've already turned off the firewalls in McAfee and Windows, that would be the next place to look.
Quote from: cholzhauer on December 08, 2010, 01:13:37 PM
OK, first thing.
is there a firewall in your speedstream? If you've already turned off the firewalls in McAfee and Windows, that would be the next place to look.
Hi Thanks for responding. I am a novice so I will appreciate your patience. I haven't turned of Mcafee firewall and I don't use windows firewall. I have allowed ICMP ping in my Mcafee settings and I have allowed connections to 66.220.274 also in my Mcafee settings. The speedstream doesn't have a firewall I don't think and I wouldn't be able to tell you if it did ???
So what is your IPv4 address?
What machine/device has that address assigned to it?
also, is there anything between the speedstream and your computer? if not, look at the gateway on your computer and try and get to that via http and see what it gets you
Quote from: broquea on December 08, 2010, 02:44:35 PM
So what is your IPv4 address?
What machine/device has that address assigned to it?
I have a public IP address that is dynamic changes slightly
A LAN IP address that is static. I have the speedstream connected to my computer so the address is assigned either to the speedstream or the computer
Quote from: cholzhauer on December 08, 2010, 02:55:17 PM
also, is there anything between the speedstream and your computer? if not, look at the gateway on your computer and try and get to that via http and see what it gets you
There is nothing it plugs straight in to the computer. I don't understand the gateway stuff.
What is the IPv4 address?
To find your gateway
Start > Run
Type in "cmd"
hit enter
type in "ipconfig"
hit enter
find your local area connection, find the gateway address
copy that address. put that address into your browser and try and browse to it.
Quote from: cholzhauer on December 08, 2010, 06:43:04 PM
What is the IPv4 address?
To find your gateway
Start > Run
Type in "cmd"
hit enter
type in "ipconfig"
hit enter
find your local area connection, find the gateway address
copy that address. put that address into your browser and try and browse to it.
I wasn't able to browse using the LAN ISP number nor the Public ISP number I was taken to a cannot display page by my internet service provider or to bling. I can access the internet all other ways through my ISP provider home page etc. etc. These number were rejected when I tried to create a connection for a tunnel the LAN number was said to be private and the public one when I entered it gave me the below message.
Error: Your IPv4 endpoint is unreachable or unstable. Please make sure ICMP is not blocked. If you are blocking ICMP, please allow 66.220.2.74 through your firewall.
Why don't you just post the output of ipconfig
The output of "ipconfig" should look something like this.
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::c856:8f0d:2a9d:53fc%10
IPv4 Address. . . . . . . . . . . : 192.168.0.64
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 7:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter IP6Tunnel:
Connection-specific DNS Suffix . :
IPv6 Address. . . . . . . . . . . : 2001:470:a:18f::2
Link-local IPv6 Address . . . . . : fe80::cde8:203:e38e:be5a%15
Default Gateway . . . . . . . . . : 2001:470:a:18f::1
I use the URL http://192.168.0.1/ (http://192.168.0.1/). You may need the user name and password to access your router.
Quote from: allen4names on December 09, 2010, 07:19:54 PM
The output of "ipconfig" should look something like this.
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::c856:8f0d:2a9d:53fc%10
IPv4 Address. . . . . . . . . . . : 192.168.0.64
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 7:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter IP6Tunnel:
Connection-specific DNS Suffix . :
IPv6 Address. . . . . . . . . . . : 2001:470:a:18f::2
Link-local IPv6 Address . . . . . : fe80::cde8:203:e38e:be5a%15
Default Gateway . . . . . . . . . : 2001:470:a:18f::1
I use the URL http://192.168.0.1/ (http://192.168.0.1/). You may need the user name and password to access your router.
I have accessed to all of the stuff but obviously haven't changed anything. It informs IP routing enabled No
Thanks
That doesnt tell us anything. We are trying to help but you aren't giving us any of the info we are asking for
Quote from: cholzhauer on December 11, 2010, 06:37:21 AM
That doesnt tell us anything. We are trying to help but you aren't giving us any of the info we are asking for
What information do you need then? I don't know how to copy the information from the C:/ window. I don't mind posting the information but will remove some references. What command shall I put in to the C:/ for the info you want?
Thanks for your help
Allen and I were asking for the IP address of your gateway so we could help you access it and determine if there was a firewall on that might be blocking your pings.
If you've turned off the McAfee firewall and the windows firewall and still aren't getting pings, either it's blocked on your gateway device or your ISP is blocking it at their level.
Broquea was asking for your public IP address so he/we could test it from his/our end.
Quote from: cholzhauer on December 11, 2010, 09:36:24 AM
Allen and I were asking for the IP address of your gateway so we could help you access it and determine if there was a firewall on that might be blocking your pings.
If you've turned off the McAfee firewall and the windows firewall and still aren't getting pings, either it's blocked on your gateway device or your ISP is blocking it at their level.
Broquea was asking for your public IP address so he/we could test it from his/our end.
I have my Mcafee firewall on all the time I have never turned it off for any reason while on the web not even to set up a tunnel and I don't use the windows one. My Public IP address is dynamic. I can supply the info you want just let me know
turn off the mcafee firewall and try.
yes your address is dynamic...what is it?
You may want to read Address Allocation for Private Internets (http://tools.ietf.org/html/rfc1918). The private IP address of your router should be static.
I think he meant that the address assigned to him by his ISP was dynamic.
Hi
My LAN IP address is static so is my default gateway IP address but my public IP address is dynamic. I have never turned off my Mcafee firewall while browsing the internet obviously for security reasons.
The public IP address that begins with 81 changes the LAN and Default gateway addresses which start with 192 do not change they are static addresses.
Try the link below.
http://192.168.254.254/ (http://192.168.254.254/)
Let us know if it takes you to the modem configuration page.
Quote from: allen4names on December 13, 2010, 05:46:59 PM
Try the link below.
http://192.168.254.254/ (http://192.168.254.254/)
Let us know if it takes you to the modem configuration page.
It sure does I use to be with tiscali who have since been taken over by Talktalk.
Is your modem firewall blocking ICMP?
Quote from: allen4names on December 14, 2010, 04:17:28 PM
Is your modem firewall blocking ICMP?
I have my firewall set up to allow ICMP ping requests? I hope that's what you mean other than that please advise!
Thanks for your help so far I'm sorry about my ignorance but I'm willing to learn!
Try setting up your tunnel again. If you get the same error message the following may help. Note that I use Windows Vista so you may need to do something else.
Control Panel > Administrative Tools > Windows Firewall with Advanced Security
Inbound Rules > Networking - Echo Request (ICMPv4-In)
Open "Windows Firewall with Advanced Security". I want you to find out if "Networking - Echo Request (ICMPv4-In)" is enabled. There should also be "Networking - Echo Request (ICMPv6-In)" right next to it so you may want to enable that too.
Quote from: allen4names on December 15, 2010, 08:02:38 PM
Try setting up your tunnel again. If you get the same error message the following may help. Note that I use Windows Vista so you may need to do something else.
Control Panel > Administrative Tools > Windows Firewall with Advanced Security
Inbound Rules > Networking - Echo Request (ICMPv4-In)
Open "Windows Firewall with Advanced Security". I want you to find out if "Networking - Echo Request (ICMPv4-In)" is enabled. There should also be "Networking - Echo Request (ICMPv6-In)" right next to it so you may want to enable that too.
I'm using windows xp home edition. I have windows firewall disabled because I am using Mcafee. I think I found the area you asked me to look into in windows firewall and I think the equivalent is "Allow incoming echo request" which is already checked. I'll wait for your next post and then try to set up a tunnel.
Cholzhauer may know something about McAfee but I don't.
I know enough to dislike it ;)
For testing, we should just disable the McAfee firewall. Unless you know how to unblock ICMP and are confident that McAfee knows what to do with protocol 41, you should disable it for testing
I have the firewall set up to allow 66.220.2.74 and allow ICMP ping requests but it still won't allow me to create a tunnel. Are you telling me to disable Mcafee firewall and then try to create a tunnel with no shield or shall I just disable Mcafee and use Window's firewall while trying to create the tunnel. Where would I find protocol 41 and allow it in Mcafee.
Confused I am.
Turn off all firewalls. Yes, I know it's not "normal" but we need to rule things out
I think I've actually seen 1 report of Norton actually filtering out Protocol 41, and when it was disabled, the tunnel worked. No idea if it is true for other software firewall solutions under Windows.
Quote from: cholzhauer on December 17, 2010, 12:16:12 PM
Turn off all firewalls. Yes, I know it's not "normal" but we need to rule things out
This might be somewhat dangerous don't you think!
For troubleshooting the problem NO it is not. It is the first thing that should be done, and left off until the problem is solved and you have your tunnel working properly.
Are there instructions on how to create a tunnel using windows XP? I have a dynamic public ISP address as well will this affect the tunnel? What about when I turn my Firewall back on ......???
If you get past your ICMP problem you should see "Example IPv6 Tunnel Configurations by OS" at the bottom of the Tunnel Details page. As for your dynamic IP address this incomplete batch script may help.
rem The variables in this script need to be set.
rem set DIRPATH =
rem set IPV4ADDR =
rem set MD5PASS =
rem set USERID =
rem set GTUNID =
cd %DIRPATH%
"C:\Program Files\GnuWin32\bin\wget" --no-check-certificate "https://ipv4.tunnelbroker.net/ipv4_end.php?ipv4b=%IPV4ADDR%&pass=%MD5PASS%&user_id=%USERID%&tunnel_id=%GTUNID%"
del /p "ipv4_end.php?ipv4b=%IPV4ADDR%&pass=%MD5PASS%&user_id=%USERID%&tunnel_id=%GTUNID%"
exit
You will need wget and set the variables. Information about wget can be found here (http://www.gnu.org/software/wget/).
EDIT
You should also check into setting the IPv6 nameserver value to 2001:470:20::2.
EDIT
I corrected the script. It needs to delete the downloaded file not give you an error message.
Sorry for the delay in my posting, First of all as I think we all know I want to set up a tunnel. I have an dynamic ip address so I don't understand the scipt scenario. What do I do with the scipt and are there windows XP set up instructions for a tunnel. If as you say I'm going to have to take down my firewall temporarily down I am going to need to be very quick setting up. advice appreciated
Don't worry about the script for now.
Turn the firewall off and see if everything works.
Quote from: cholzhauer on January 06, 2011, 12:19:24 PM
Don't worry about the script for now.
Turn the firewall off and see if everything works.
Okay sorry about the delay in getting back... Okay, so I am going to take down my firewall while I set up a tunnel. I have a few questions before I attempt this.
Are you sure this will work? I have a dynamic IP address
Will my ISP allow me to set up a tunnel?
I'm running windows XP home edition is there a tutorial of how to go through the motions of setting up a tunnel using this operating system?
Am I blessed with this being straight forward if it works once I temporarily take down the firewall?
I have had to change my router to a speedtouch due to problems that's why I haven't been able to post here.
I temporarily took down my firewall and realtime scanning and attempted to set up a tunnel. This is the message I got:
Error: Your IPv4 endpoint is unreachable or unstable. Please make sure ICMP is not blocked. If you are blocking ICMP, please allow 66.220.2.74 through your firewall.
Do you need to be a Rocket scientist or a super IT specialist or engineer to set up a tunnel. Let's face it. It isn't straight forward is it!
I try to set up a tunnel from London and then I tried to set up a tunnel from Amsterdam on two occasions so that was 3 attempts with the firewall and realtime scanning down. Result taking down the firewall hasn't made any difference.
help and advice would be appreciatied
Quote from: alberto90 on January 29, 2011, 05:41:16 AM
I temporarily took down my firewall and realtime scanning and attempted to set up a tunnel. This is the message I got:
Error: Your IPv4 endpoint is unreachable or unstable. Please make sure ICMP is not blocked. If you are blocking ICMP, please allow 66.220.2.74 through your firewall.
Do you need to be a Rocket scientist or a super IT specialist or engineer to set up a tunnel. Let's face it. It isn't straight forward is it!
I try to set up a tunnel from London and then I tried to set up a tunnel from Amsterdam on two occasions so that was 3 attempts with the firewall and realtime scanning down. Result taking down the firewall hasn't made any difference.
help and advice would be appreciatied
When you can ping your 81.178.217.160 from another connection it will be possible to create a tunnel. So just try to get it responding to pings, then you're done. Easy.
Edit: made a little correction
Quote from: hisken on January 29, 2011, 07:00:15 AM
Quote from: alberto90 on January 29, 2011, 05:41:16 AM
I temporarily took down my firewall and realtime scanning and attempted to set up a tunnel. This is the message I got:
Error: Your IPv4 endpoint is unreachable or unstable. Please make sure ICMP is not blocked. If you are blocking ICMP, please allow 66.220.2.74 through your firewall.
Do you need to be a Rocket scientist or a super IT specialist or engineer to set up a tunnel. Let's face it. It isn't straight forward is it!
I try to set up a tunnel from London and then I tried to set up a tunnel from Amsterdam on two occasions so that was 3 attempts with the firewall and realtime scanning down. Result taking down the firewall hasn't made any difference.
help and advice would be appreciatied
When you can ping your 66.220.2.74 from another connection it will be possible to create a tunnel. So just try to get it responding to pings, then you're done. Easy.
Not quite sure what your talking about I can ping 66.220.2.74 from my internet connection. ICMP connections are allowed through my firewall so is 66.220.2.74. Can someone explain this? 66.220.2.74 is responding to pings from my connection. But I still can't set up a tunnel.
what is your IPv4 address?
Quote from: broquea on January 29, 2011, 10:55:07 AM
what is your IPv4 address?
81.178.217.160
That is what it says on whatsmyip.com
Yup, can't ping your IP, that was done from the tunnelbroker.net machine. Is that actually configured on your computer, or some sort of NAT appliance?
~$ ping -c 5 81.178.217.160
PING 81.178.217.160 (81.178.217.160) from 66.220.2.74 : 56(84) bytes of data.
--- 81.178.217.160 ping statistics ---
5 packets transmitted, 0 received, 100% packet loss, time 4010ms
Quote from: broquea on January 29, 2011, 11:08:18 AM
Yup, can't ping your IP, that was done from the tunnelbroker.net machine. Is that actually configured on your computer, or some sort of NAT appliance?
~$ ping -c 5 81.178.217.160
PING 81.178.217.160 (81.178.217.160) from 66.220.2.74 : 56(84) bytes of data.
--- 81.178.217.160 ping statistics ---
5 packets transmitted, 0 received, 100% packet loss, time 4010ms
Not quite sure what this means what is an NAT appliance
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\>ping 66.220.2.74
Pinging 66.220.2.74 with 32 bytes of data:
Reply from 66.220.2.74: bytes=32 time=172ms TTL=52
Reply from 66.220.2.74: bytes=32 time=173ms TTL=52
Reply from 66.220.2.74: bytes=32 time=172ms TTL=52
Reply from 66.220.2.74: bytes=32 time=172ms TTL=52
Ping statistics for 66.220.2.74:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 172ms, Maximum = 173ms, Average = 172ms
Your typical consumer router/firewall. You probably just need to configure it to respond to pings.
Quote from: alberto90 on January 29, 2011, 11:17:20 AM
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\>ping 66.220.2.74
Pinging 66.220.2.74 with 32 bytes of data:
Reply from 66.220.2.74: bytes=32 time=172ms TTL=52
Whoops, I was wrong. Posted my reply a bit too fast I guess. Obviously you need to be able to ping your own external IP4 from another connection, not that 66.220 address from HE. I misread the error message you quoted :)
So yeah, as jimb already said: just configure your router to respond to pings.
Quote from: jimb on January 29, 2011, 01:59:18 PM
Your typical consumer router/firewall. You probably just need to configure it to respond to pings.
How do I do this? I have recently been sent a new speedtouch router because the other router I had was giving me severe connection problems at some websites. I'm a bit dubious as to if my ISP will allow me to set up a tunnel.
Thanks for answering
Quote from: hisken on January 29, 2011, 03:28:21 PM
Quote from: alberto90 on January 29, 2011, 11:17:20 AM
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\>ping 66.220.2.74
Pinging 66.220.2.74 with 32 bytes of data:
Reply from 66.220.2.74: bytes=32 time=172ms TTL=52
Whoops, I was wrong. Posted my reply a bit too fast I guess. Obviously you need to be able to ping your own external IP4 from another connection, not that 66.220 address from HE. I misread the error message you quoted :)
So yeah, as jimb already said: just configure your router to respond to pings.
Could you explain this to me? Thanks
Quote from: alberto90 on January 30, 2011, 05:42:23 AM
Could you explain this to me? Thanks
Open a command prompt.
telnet *your-internal-router-ip*
user: Administrator
password: blank or whatever you set
service system ifadd name=PING_RESPONDER group=wan
connection unbind application=IP6TO4 port=0
saveall
exit
exit
Deja vu, seen this before on this forum :o
How do I find my internal router IP? or do I just type in your example? Please forgive my ignorance I have never done anything like this before there is so much to learn ??? :o
Go to any of your internal hosts. The default router will be the IP of your firewall's internal interface.
Quote from: jimb on January 30, 2011, 05:38:37 PM
Go to any of your internal hosts. The default router will be the IP of your firewall's internal interface.
How do I locate these? I'm running windows xp home edition
Start > Run
type in "cmd"
hit enter
type in "ipconfig /all"
copy and paste the output onto this page and hit submit.
C:\Documents and Settings\>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : D9MHBN1J
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : tiscali.co.uk
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : tiscali.co.uk
Description . . . . . . . . . . . : Intel(R) PRO/100 VE Network Connection
on
Physical Address. . . . . . . . . : 00-13-20-1B-99-68
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.64
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.254
DHCP Server . . . . . . . . . . . : 192.168.1.254
DNS Servers . . . . . . . . . . . : 192.168.1.254
Lease Obtained. . . . . . . . . . : 31 January 2011 10:56:45
Lease Expires . . . . . . . . . . : 01 February 2011 10:56:45
The address of your router is
192.168.1.254
Quote from: cholzhauer on January 31, 2011, 07:38:03 AM
The address of your router is
192.168.1.254
Thanks! After I bypass the password bit I get this. I've used my windows admin pass and my ISP pass but they don't seem to let me pass this stage. I'll retry them all
Username : Administrator
Password :
------------------------------------------------------------------------
______ SpeedTouch 510
___/_____/\
/ /\ 6.1.18.6
_____/__ / \
_/ /\_____/___ \ Copyright (c) 1999-2006, THOMSON
// / \ /\ \
_______//_______/ \ / _\/______
/ / \ \ / / / /\
__/ / \ \ / / / / _\__
/ / / \_______\/ / / / / /\
/_/______/___________________/ /________/ /___/ \
\ \ \ ___________ \ \ \ \ \ /
\_\ \ / /\ \ \ \ \___\/
\ \/ / \ \ \ \ /
\_____/ / \ \ \________\/
/__________/ \ \ /
\ _____ \ /_____\/
\ / /\ \ /___\/
/____/ \ \ /
\ \ /___\/
\____\/
------------------------------------------------------------------------
_{Administrator}=>
From the manual
If prompted, enter the User name and Password for your SpeedTouch™
security settings and click OK.
The factory default user is 'Administrator'. Its password is blank,
meaning you do not have to enter anything in the password field. It is
advisable to specify another user name and password to protect your
SpeedTouch™ from security violation during the configuration
procedure (see " Access Control" on page 13), or as described in
"3.4 Basic Security" on page 18.
If it's not blank, the password was set by someone and if you don't know it, you need to reset it to factory defaults
Quote from: cholzhauer on February 01, 2011, 05:25:21 AM
From the manual
If prompted, enter the User name and Password for your SpeedTouch™
security settings and click OK.
The factory default user is 'Administrator'. Its password is blank,
meaning you do not have to enter anything in the password field. It is
advisable to specify another user name and password to protect your
SpeedTouch™ from security violation during the configuration
procedure (see " Access Control" on page 13), or as described in
"3.4 Basic Security" on page 18.
If it's not blank, the password was set by someone and if you don't know it, you need to reset it to factory defaults
I will try my to obtain the password from my ISP they sent me the router so they should be able to provide me the password. Watch this space. Thanks for all help so far
I'm still not sure if this is going to work. My ISP have told me that I may not be able to access the router using the telnet commands and if I reset it to factory settings they have told me there are still no guarantees that I will be able to change the password I have the feeling that the passwords may be set on installation. They said they don't support proxy server set ups when I pressed them on the subject obviously they asked me why I wanted access to the router.
Changing the speedtouch password from the website does nothing I have used a number of passwords my talktalk email and password, Admin, password, etc none of it works with the cmd telnet when I enter the password. I can't find anywhere else on the speed touch website where it needs to be entered.
http://192.168.1.254/
I got installation instructions very similar to the below when I installed this 510 v6 a few weeks ago and all I put in was my talktalk username and password.
http://support.talktalk.co.uk/cgi-bin/uk_tiscali.cfg/php/enduser/std_adp.php?p_faqid=521&p_created=1175687424&p_sid=6Oua_qmk&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NTIsNTImcF9wcm9kcz0wJnBfY2F0cz0mcF9wdj0mcF9jdj0mcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1zcGVlZHRvdWNoIDUxMA!!&p_li=&p_topview=1 (http://support.talktalk.co.uk/cgi-bin/uk_tiscali.cfg/php/enduser/std_adp.php?p_faqid=521&p_created=1175687424&p_sid=6Oua_qmk&p_accessibility=0&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NTIsNTImcF9wcm9kcz0wJnBfY2F0cz0mcF9wdj0mcF9jdj0mcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1zcGVlZHRvdWNoIDUxMA!!&p_li=&p_topview=1)
Quote from: alberto90 on January 31, 2011, 01:04:32 PM
Quote from: cholzhauer on January 31, 2011, 07:38:03 AM
The address of your router is
192.168.1.254
Thanks! After I bypass the password bit I get this. I've used my windows admin pass and my ISP pass but they don't seem to let me pass this stage. I'll retry them all
Username : Administrator
Password :
------------------------------------------------------------------------
______ SpeedTouch 510
___/_____/\
/ /\ 6.1.18.6
_____/__ / \
_/ /\_____/___ \ Copyright (c) 1999-2006, THOMSON
// / \ /\ \
_______//_______/ \ / _\/______
/ / \ \ / / / /\
__/ / \ \ / / / / _\__
/ / / \_______\/ / / / / /\
/_/______/___________________/ /________/ /___/ \
\ \ \ ___________ \ \ \ \ \ /
\_\ \ / /\ \ \ \ \___\/
\ \/ / \ \ \ \ /
\_____/ / \ \ \________\/
/__________/ \ \ /
\ _____ \ /_____\/
\ / /\ \ /___\/
/____/ \ \ /
\ \ /___\/
\____\/
------------------------------------------------------------------------
_{Administrator}=>
At this point you are in the router at a command prompt. Use the commands Hisken gave you to enable ping response.
May as well have another go at this. What shall I do now I'm at the cprompt?
Looks like interest has been lost.
I'm preparing to give up with this. Can anyone help? It will test your patience and professional knowledge and tutoring skills. That's what I thought help forums were for :)
Thanks
:-* :-* :-* :-* ;D ;D