Hurricane Electric's IPv6 Tunnel Broker Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to Hurricane Electric's Tunnelbroker.net forums!

Author Topic: Configuring a tunnel under Cisco & Juniper & Vyatta & Alcatel  (Read 29406 times)

broquea

  • Sr. Network Engineer, HE.NET AS6939
  • Administrator
  • Hero Member
  • *****
  • Posts: 1667
    • View Profile
    • Another IPv6 Blog...
Configuring a tunnel under Cisco & Juniper & Vyatta & Alcatel
« on: February 08, 2008, 02:03:56 PM »

Users will always be able to view the example configurations provided in the tunnelbroker.net interface, however we also wanted to make them available on the forums. I'll cover the Cisco & Juniper & Vyatta commands used. I won't be using valid IPv4/IPv6 information in the examples, but the example configurations in the broker's interface will provide the full commands with your relevant account information.

Legend of variables:
$ipv4a = tunnel server's IPv4 IP
$ipv4b = user's IPv4 IP
$ipv6a = tunnel server's side of point-to-point /64 allocation
$ipv6b = user's side of point-to-point /64 allocation

Cisco
interface tunnel0
 description Hurricane Electric IPv6 Tunnel Broker
 no ip address
 ipv6 enable
 ipv6 address $ipv6b
 tunnel source $ipv4b
 tunnel destination $ipv4a
 tunnel mode ipv6ip
ipv6 route ::/0 tunnel0

Juniper
interfaces {
    gr-1/0/0 {
         unit 0 {
             tunnel {
                 source $ipv4b;
                 destination $ipv4a;
             }
             family inet6 {
                 address $ipv6b;
             }
         }
     }
}
rib inet6.0 {
    static {
        route ::/0 {
            $ipv6a ;
        }
    }
}

Vyatta
configure
edit interfaces tunnel tun0
set encapsulation sit
set local-ip $ipv4b
set remote-ip $ipv4a
set address $ipv6b/64
set description "HE.NET IPv6 Tunnel"
exit
set protocols static interface-route6 ::/0 next-hop-interface tun0
commit

Alcatel Lucent Omniswitch 6850
ipv6 interface hetunnel tunnel 1
ipv6 interface hetunnel tunnel source $ipv4b destination $ipv4a
ipv6 address $ipv6b/64 hetunnel
ipv6 static-route ::/0 gateway $ipv6a
« Last Edit: August 05, 2010, 08:47:09 AM by broquea »
Logged

broquea

  • Sr. Network Engineer, HE.NET AS6939
  • Administrator
  • Hero Member
  • *****
  • Posts: 1667
    • View Profile
    • Another IPv6 Blog...
Configuring a Juniper NS-5GT Netscreen (ScreenOS) firewall appliance
« Reply #1 on: December 27, 2008, 01:22:53 PM »

This was submitted by user techniq for his NetScreen 5GT:

set interface tunnel.1 zone Untrust
set interface tunnel.1 ipv6 mode host
set interface tunnel.1 ipv6 ip $ipv6b/64
set interface tunnel.1 ipv6 enable
set interface tunnel.1 tunnel encap ip6in4 manual
set interface tunnel.1 tunnel local-if untrust dst-ip $ipv4
unset interface tunnel.1 ipv6 nd nud
set interface tunnel.3 ipv6 nd dad-count 0
set route ::/0 interface tunnel.1 gateway $ipv6a
Logged

broquea

  • Sr. Network Engineer, HE.NET AS6939
  • Administrator
  • Hero Member
  • *****
  • Posts: 1667
    • View Profile
    • Another IPv6 Blog...
Re: Configuring a tunnel under Cisco & Juniper
« Reply #2 on: August 11, 2009, 10:52:36 PM »

A user with a new Juniper router/firewall has an updated config for SRX models: http://forums.juniper.net/jnet/board/message?board.id=srx&thread.id=234
Logged

broquea

  • Sr. Network Engineer, HE.NET AS6939
  • Administrator
  • Hero Member
  • *****
  • Posts: 1667
    • View Profile
    • Another IPv6 Blog...
Re: Configuring a tunnel under Cisco & Juniper & Vyatta
« Reply #3 on: November 10, 2009, 02:53:11 PM »

A user of ours submitted a Vyatta example configuration. Updated this thread's top post and added it to example configurations inside the broker.
Logged